收藏本站
j)
k)
l)
m)
n)
o)
p)
If the host has not placed the result of its CRC calculation on D[15:00] since first driving D[15:00]
during (9), the host shall place the result of its CRC calculation on D[15:00] (see 6.3.2.5 ).
The host shall negate -DMACK no sooner than t MLI after the device has asserted DSTROBE and negated
DMARQ and the host has asserted STOP and negated -HDMARDY, and no sooner than t DVS after the
host places the result of its CRC calculation on D[15:00].
The device shall latch the host’s CRC data from D[15:00] on the negating edge of -DMACK.
The device shall compare the CRC data received from the host with the results of its own CRC
calculation. If a miscompare error occurs during one or more Ultra DMA burst for any one command,
at the end of the command, the device shall report the first error that occurred (see 6.3.2.5 ).
The device shall release DSTROBE within t IORDYZ after the host negates -DMACK.
The host shall neither negate STOP nor assert -HDMARDY until at least t ACK after the host has negated
-DMACK.
The host shall not assert -IORD, -CS0, -CS1, DA2, DA1, or DA0 until at least t ACK after negating DMACK.
Figure 7: Ultra DMA Data-In Burst Host Termination Timing
Notes: The definitions for the STOP, HDMARDY, and DSTROBE signal lines are no longer in effect after
DMARQ and DMACK are negated.
6.3.2.4.6 Initiating an Ultra DMA Data-Out Burst
An Ultra DMA Data-out burst is initiated by following the steps lettered below. The timing diagram
is shown in Figure 8: Ultra DMA Data-Out Burst Initiation Timing. The timing parameters are
specified in Table 22: Ultra DMA Data Burst Timing Requirements and are described in Table 23: Ultra DMA
Data Burst Timing Descriptions.
The following steps shall occur in the order they are listed unless otherwise specifically allowed:
a) The host shall keep -DMACK in the negated state before an Ultra DMA burst is initiated.
b) The device shall assert DMARQ to initiate an Ultra DMA burst.
c)
Steps (c), (d), and (e) may occur in any order or at the same time. The host shall assert STOP.
d) The host shall assert HSTROBE.
Swissbit AG
Industriestrasse 4
Swissbit reserves the right to change products or specifications without notice.
Revision: 1.00
CH-9552 Bronschhofen
Switzerland
www.swissbit.com
industrial@swissbit.com
P-120_data_sheet_PA-QxBO_Rev100.doc
Page 24 of 76
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SFPK-SL CONN SFP CAGE
SFSA16GBV1BR4TO-I-QT-226-STD FLASH SLC UDMA/MDMA/PIO 16GB
SFSA32GBQ1BR8TO-I-QT-226-STD FLASH SLC UDMA/MDMA/PIO 32GB
SFSA32GBU1BR4TO-I-NC-216-STD FLASH X-200M SLC MSATA 32GB
SFSA32GBV1BR4TO-I-NC-216-STD FLASH X-200S SLC SLIM SATA 32GB
SFSA64GBQ1BR8TO-I-NC-216-STD FLASH SSD UDMA IND 2.5" 64GB
SFSO4404NR FEMALE SCREWLOCK 4-40 .197"
SFW22R-1STE1 SFW22R-1STE1-FFC/FPC CONN
相关代理商/技术参数
SFPA32GBQ1BO8TO-I-QT-243-STD 制造商:SWISSBIT NA INC 功能描述:FLASH
SFPA36AT0250 制造商:General Electric Company 功能描述:SFP 3P 600V 250A
SFPA4096Q1BO2TO-C-DT-243-STD 制造商:SWISSBIT NA INC 功能描述:FLASH
SFPA4096Q1BO2TO-I-DT-223-STD 功能描述:FLASH SSD SMART UDMA 2.5" 4GB RoHS:是 类别:计算机，办公室 - 元件，配件 >> 固态硬盘驱动器 系列:P-120 标准包装:1 系列:- 存储容量:64GB 存储器类型:闪存 - NAND 其它名称:VL 64 GB SSHD KITVL64GBSSHDKIT
SFPA4096Q1BO2TO-I-DT-243-STD 制造商:SWISSBIT NA INC 功能描述:FLASH
SFPA-53 制造商:未知厂家 制造商全称:未知厂家 功能描述:Schottky Barrier Diodes
SFPA-63 制造商:SANKEN 制造商全称:Sanken electric 功能描述:Schottky Barrier Diodes (Surface Mount) 30V
SFPA-73 制造商:未知厂家 制造商全称:未知厂家 功能描述:Schottky Barrier Diodes